DrCJW Slingerland Article 3

[Webmaster]

Article was just uploaded and is an excellent guide to Slingerland shells.

Click Here (http://www.vintagesnaredrums.com/drcjw/articles.html)

Hope you all enjoy it!!!

David
Webmaster

[Deacon Bob]

Article was just uploaded and is an excellent guide to Slingerland shells.

Click Here (http://www.vintagesnaredrums.com/drcjw/articles.html)

Hope you all enjoy it!!!

David
Webmaster
Dave
Thank You!!! I just joined the site. I own a 1970"s Slingerland Kit. It has some delamination at the seams. Is there a fix?

Thank You

[Webmaster]

Are you saying the finish is coming up at the seams? or the shell wood is seperating at the plys?

Let me know

David

[Deacon Bob]

Are you saying the finish is coming up at the seams? or the shell wood is seperating at the plys?

Let me know

David
Dave
The finish is seperating from the wood.

[Webmaster]

I have heard a few fixes for that and one is using
super glue (acetone), very carefully and with great care. You should tape both edges of the seam (and shell edge), because if it runs, you will ruin the wrap.

The real glue that is used for applying wrap to the shell requires
a process of applying the adhesive to both the shell and the back of the wrap then letting that cure and eventually putting the two pieces together. (3M Fastbond Contact Cement 30nf). Use a small paint brush.

There are glue experts out there and they might have a better glue for this.

After it is glued you will need to clamp it with blocks of wood so you need everything ready to go and in place
for a quick clamping.

The important thing is that the glue must be perfect in the seam.

It is also recommended that you do some practice pieces first so you see how the glue reacts and understand the process.


David

[vadrums]

The best way is to peel about 2 inches away from the shell. Then you take a razor blade and carefully scrape away all of the old contact cement. You will see the white base of the wrap on the underside and scrape the area where it will rest onto the other piece. Use Weldwood Contact Cement and follow the manufactures directions. Just remember!!! Once it is layed down, it will never come apart again, so make sure you start at the lifted end and work to the other piece on the shell. You won't need any clamping with this technique and any of the extra cement can be rubbed off when dry.

[Webmaster]

I will take that as a good suggestion depending on how bad the lift is at the seam. If it is only a small section, I would personally not peel back the two inches and opt for a simpler fix. If on the other hand it is a larger section and the wrap peals back easily then the 2" method would work great.

I would also recommend caution and patience with that so the person making the fix does not do more damage to the wrap. It would be a case by case basis depending on the wrap and if it is brittle or not.

I think I might have swayed or miss-led the topic with my earlier answer, because the wrap problem is at the bearing edge and not the seam. I started on course with my answer and then went a stray!

Sorry for any confusion folks.

David

[Deacon Bob]

I have heard a few fixes for that and one is using
super glue (acetone), very carefully and with great care. You should tape both edges of the seam (and shell edge), because if it runs, you will ruin the wrap.

The real glue that is used for applying wrap to the shell requires
a process of applying the adhesive to both the shell and the back of the wrap then letting that cure and eventually putting the two pieces together. (3M Fastbond Contact Cement 30nf). Use a small paint brush.

There are glue experts out there and they might have a better glue for this.

After it is glued you will need to clamp it with blocks of wood so you need everything ready to go and in place
for a quick clamping.

The important thing is that the glue must be perfect in the seam.

It is also recommended that you do some practice pieces first so you see how the glue reacts and understand the process.


David

Thank you so much Dave!

[Deacon Bob]

The best way is to peel about 2 inches away from the shell. Then you take a razor blade and carefully scrape away all of the old contact cement. You will see the white base of the wrap on the underside and scrape the area where it will rest onto the other piece. Use Weldwood Contact Cement and follow the manufactures directions. Just remember!!! Once it is layed down, it will never come apart again, so make sure you start at the lifted end and work to the other piece on the shell. You won't need any clamping with this technique and any of the extra cement can be rubbed off when dry.

Thank you so much my brother!